All ourAutomatic
Gate Operators use the state of the art Eagle Diamond Control
Board. This board includes many new features that cannot
be found on other Automatic Gate Openers.
The Feature Selector uses an eight station switch that allows
selection of the standard features and customized installation
settings. The switch description is as follows:
Switch 1 = Slave/Master - Sets the operator to work as a
Master or a Slave.
Switch 2 = Gate Opening - Designates left or right opening.
Switch 3 = Motor Brake - If the "on" position
is selected, the gate will stop instantly when on the limit
switches. This is useful on uphill/downhill applications
and on all Fail-Safe operators.
Switch 4 = Reverse Loop - Sets the reverse loop to be "normally"
open or to "normally" close. It is useful in Fail-safe
applications.
Switch 5 = One Pass (on/off) - This tailgating feature works
with the safety loop to allow only one car to pass. After
the car passes, the gate closes instantly. If a second car
approaches the gate stops. The operator resumes closing
after the car leaves.
Switch 6 = Stop-Reverse - This radio feature allows the
transmitter to work as a three button station and is useful
for a partial opening. If selected, the first command will
open the gate, the second will stop the gate, and the third
will close the gate.
Switch 7 = Alarm Reset (on/off) - If the "on"
position is selected (after five minutes "shut down"
time period) the operator will reset and any input will
be accepted. Normally, the power must be turned off to reset.
Switch 8 = Close Timer (on/off) - Sets the timer to close
on the "on" or "off" position.
The Eagle Automatic
Gate Openers Diamond Control Board uses an unique Master/Slave
system that requires only two wires. In addition, the Diamond
board has global inputs. These inputs give the installer
the option to connect accessories to the Master or to the
Slave. Another stand out feature is the "open and close
delay", this function is easily selected on the Slave
board.
On the Master Control one has the option to select the following
features: one pass mode, stop-reverse mode, alarm reset
mode, and close timer.
The Slave Control was uniquely designed to communicate to
the master board all of the delay functions.
Switch 5 = Open Delay Slave (on/off) - Selecting the dipswitch
to the "on" position delays the slave operator
by one second on the open cycle. This is useful with a magnetic
lock application.
Switch 6 = Open Delay Master (on/off) - Selecting the dipswitch
to the "on" position delays the mast operator
by one second on the open cycle. This is useful with a magnetic
lock application.
Switch 7 = Close Delay Slave (on/off) - Selecting the dipswitch
to the "on" position delays the slave operator
by 1-6 seconds on the close cycle. You can set the delay
time desired by adjusting the delay potentiometer.
Switch 8 = Close Delay Master (on/off) - Selecting the dipswitch
to the "on" position delays the master operator
by 1-6 seconds on the close cycle. You can set the delay
time desired by adjusting the delay potentiometer.
The Eagle Automatic
Gate Operators Diamond Control Board uses LEDs to indicate
the status of the inputs and outputs of the gate operator.
The Automatic Gate
Openers Diamond board has several unique safety features.
In case of overload, if the motor reaches the stall amp
for 3 seconds, it will automatically shut down.
If the gate hits an obstruction while closing, it will re-open.
If it hits an obstruction while opening, it will stop, reverse
6 inches and stop again. The sensitivity is adjustable separately
for the open and close cycle.
If the gate hits an object twice while closing or opening,
the system will shut down for 5 minutes. On the Diamond
board you have two options of reset mode. Selecting the
"off" position will require a manual reset of
the board if the previous happens. However, by selecting
the "on" position, the system will automatically
reset itself.
Global Inputs allow
the installer the option to connect accessories to the Master
or to the Slave - key switch, keypad, exit loop, phantom
loop, reverse loop, edge sensor, open, stop, and close.
The Receiver terminal
is mounted on the control box for easy installation and
is pre-wired for a 3-wire or a 4-wire receiver.
The
Diamond board's Outputs include on board 24VDC for MAG
Lock, alarm, and 24VAC auxiliary power.
The
Diamond board has an Adjustable Timer that can be set
from 1 to 6 seconds. The maximum run time is 6 seconds,
after which if the gate hasn't reached the open or close
limit it will automatically shut down.
|
